Upgrade Liquid Epoxy Resin Clear Epoxy Resin
MTB- 6048 is a crystal-clear, low-viscosity epoxy resin and is produced and distributed exclusively in premium quality. MTB-6048 is ideal for almost any application. For example: in the jewelery sector, table manufacturing, for river tables for floors, ponds,aquarium and terrarium construction, as well as for boat, ship and aircraft construction.
| Item (MTB-2209) |
Epoxy Resin(A ) |
Epoxy Resin(B ) |
| Color |
Transparent Liquid |
Transparent Liquid |
| Viscosity@25ºC(mpa.s) |
380-450 |
30-40 |
| Mix Ratio(by weight) |
3 |
1 |
| Hardness(Shored) |
75-80 |
| Operation time(100g mixed glue ,25ºC) |
50-60minutes |
| Curing Time(25ºC) |
24-26hours |
| Curing Time(35ºC) |
8hours |
| Curing Time(25ºC) |
6-12months |
Upgrade Liquid Epoxy Resin Clear Epoxy Resin
Product Advantage
* Non-toxic
* 100% Solid
* VOc Free
* Solvent Free
* Crystal Clear
* Epoxy Resin and hardener,mix ratio of 1:1
* Thick Pour to 2"-4"
1. Mirror-Like Crystal Clear Finish
The Highest super wet with gloss finish with unparalleled depth and clarity that is formulated to use within all coating and step casting applications
2. High-Grade UV Resistance
All epoxies will turn yellow overtime. What makes our Super clear Epoxy resin crystal clear kit different is our specific high-grade additive formulation. Ours will yellow less and remain ultra-crystal-clear over a longer period of time than any of our competitors. Our products are made for you, and made to last, bar none.
3. Integrate Color With Ease
Perfectly suited for accepting and dispersing mica powder pigments, liquid pigments paste and alcohol inks and dyes.It is the ideal epoxy for evenly distributing color and suspending inks and powders. Paint, acrylic paint and oil based paint are not recommended to use with epoxy, and can have negative results.
4.FDA Grade &MSDS
To consider a product food safe, the end product must be tested. Since every project is made by a different artisan and not in the same exact way, and our product comes in two parts that must be mixed, every finished piece must be tested. Once Super Clear Table Top Epoxy has cured, it becomes safe, per FDA code, 21CFR175.300 which states "Resinous and polymeric coatings may be safely used as the food contact surface of articles intended for use in producing, manufacturing,packing, processing, preparing, treating, packaging, transporting, or holding food" and can be used as a "functional barrier between the food and the substrate" and "intended for repeated food-contact and use."
5.Advanced Formula for Strengt
With tables, table tops and countertops you need durability.That's why we crafted an epoxy formulation with an 80+ Shore D Strength Rating when fully cured.
6. 100% VOC Free & Practically Odorless &Self Leveling&Zero Shrinking
Upgrade Liquid Epoxy Resin Clear Epoxy Resin
How to use
Step 1: The ideal working temperature is around a constant 77°F. Best results can be obtained at constant temperatures between 70°F and 85°F, in a clean, dry, dust-free environment. Avoid working in high humidity. We recommend using this product on a leveled and flat work surface.
Step 2: Measure product in accordance with your intended use. Prepare 3 parts Base Resin to 1 part Curing Agent by liquid volume.Pour the Curing Agent first and then the Base Resin into a clean, smooth-sided container large enough to hold all the liquid and allow room for mixing.
Step 3: The material must be mixed thoroughly for at least 3 minutes. Be sure to scrape the container sides, bottom, and corners as you mix. Be careful not to whip excessive air into the mixture. If mixing a gallon, use a power mixer set to "hand speed." For smaller quantities, use stir sticks. Do not mix more than a gallon. Pour into a new, clean container and mix for an additional minute.
Step 4: Pour the mixed resin onto the surface and distribute evenly with a squeegee or gloved hand. Continue to pour remaining material to achieve the desired thickness, allowing the resin to flow evenly over the project's sides. Resin can be poured up to 1/4" thick per pour.
Step 5: Use a heat source such as a heat gun to remove any bubbles by adding a small amount of heat to the surrounding area. The bubble will rise to the surface and pop.
Step 6: If you are going to make a second pour, the first pour should still be slightly sticky. Once the second pour is made, bubbles may once again need to be removed. Material will feel hard after 45-60 minutes, cure to the point of workability within 24 hours, but full cure and maximum hardness can require up to 7 days, depending upon the temperature.
Packing
Neutral Package
---16OZ/kit
---32OZ/kit
---1gallon/kit
---3gallon/kit
---20KG/kit
Accept package and label OEM&ODM
FAQ
1.Q: What's the best way to mix this?
A: You'll want to make sure that you have 2 parts base resin and 1 part curing agent measured precisely, by volume. Pour each into your mixing bucket, and we recommend mixing by hand for at least 3 minutes and between 3-5 minutes or until it is fully mixed. Be careful to scrape the
sides while mixing, but when pouring, do not scrape the sides. This can impart unmixed material that may cling to the side and has not been incorporated. Don't worry about any bubbles in the mixture, they will all work themselves out.
2.Q: How long does it take to cure, and what temperatures can I pourthis in?
A: Our optimum environment temperature range is 72° - 84°F (in a clean, temperature controlled environment. In that temperature range, it will begin to gel in 20-30 minutes, and cure rock hard within 24 hours.Temperatures under 70° will slow the curing process even more, and the closer you get to 60° the curing process will stop. Above 85°, it will begin to accelerate curing, leading to cracking, shrinking and other negative results.
3.Q: Is your epoxy FDA Compliant?
A: The short answer is, yes. Once our epoxy has cured, it becomes safe,per FDA code, 21CFR175.300 which states "Resinous and polymeric coatings may be safely used as the food-contact surface of articlesintended for use in producing, manufacturing, packing, processing,
preparing, treating, packaging, transporting, or holding food" and can be used as a "functional barrier between the food and the substrate".
4.When Can I Demould?
A: Our optimum environment temperature range is 72° - 84°F in a clean temperature controlled environment. In that temperature range, you can demould between 18 and 24 hours, and its optimal workability will be at 24-30 hours. At 30 hours it will sand and plane as easy as wood!
Audited Supplier 
){kind=link}